# Springs, Utah

Springs in Utah. 68°F (20°C). Short Walk. Beaver County.

- Page: https://www.soakingsprings.com/hot-springs/utah/springs-beaver-county
- Source: Soaking Springs, researched and maintained by Armen Suny
- Updated: 2026-09-14

## Can you soak at Springs?

The water leaves the ground at 68°F, cooler than most swimming pools. It's a short walk from the road. We haven't confirmed whether it has a pool or charges a fee.

## Key facts

| Fact | Value |
|---|---|
| Source water temperature | 68°F (20°C) (USGS record; developed pools are often cooled) |
| pH | 7.5 (Slightly Alkaline) |
| Total dissolved solids | 558 mg/L |
| Elevation | 5,020 ft |
| Access | Short Walk, 0.2 mi from the nearest road |
| County | Beaver County |
| Nearest town | Milford |
| Coordinates | 38.76200, -112.87000 |
| Best months to soak | January, December, February (largest gap between water and average air temperature) |

## About Springs

Springs is the whole name on the record for this unnamed thermal point in Beaver County, Utah. Milford is the closest town, about 26 miles off. Barely warm water. A USGS crew sampled it back in 1985, and nothing since then has put an owner or an access rule on file.

Roughly a fifth of a mile from a road that goes unnamed on the record. Around five thousand feet in dry basin country, ten inches of precipitation a year and a winter snowfall of about two and a half feet. No land unit appears.

Winter heads the list on record. The water is too cool to soak in. No campground is listed within range, and Milford is the closest town of any size on file. Because ownership is unrecorded, verify the land before walking out to it.

## Water chemistry

Lab sample from 1985-09-12 (Water Quality Portal).

| Measure | Value |
|---|---|
| pH | 7.5 |
| Total dissolved solids | 558 mg/L |
| Calcium | 45 mg/L |
| Magnesium | 14 mg/L |
| Sodium | 71 mg/L |
| Sulfate | 48 mg/L |
| Chloride | 110 mg/L |

## Nearby

- Nearest city page: [Hot springs near Milford](https://www.soakingsprings.com/hot-springs/near/utah/milford), 1 mi away
- State page: [Hot springs in Utah](https://www.soakingsprings.com/hot-springs/utah)
- [Coyote Spring, UT](https://www.soakingsprings.com/hot-springs/utah/coyote-spring-2): 68°F source, pH 7.5, TDS 558 mg/L, Short Walk, near Milford, Beaver County
- [Roosevelt Hot Springs, UT](https://www.soakingsprings.com/hot-springs/utah/roosevelt-hot-springs): 133°F source, pH 7.7, Roadside, near Milford, Beaver County
- [Meadow Hot Springs, UT](https://www.soakingsprings.com/hot-springs/utah/meadow-hot-springs): 106°F source, pH 6.9, TDS 5,120 mg/L, Roadside, near Fillmore, Millard County
- [Sulphurdale, UT](https://www.soakingsprings.com/hot-springs/utah/sulphurdale): 72°F source, Short Walk, near Beaver, Beaver County
- [Hatton Hot Spring, UT](https://www.soakingsprings.com/hot-springs/utah/hatton-hot-spring): 100°F source, pH 7.1, Roadside, near Fillmore, Millard County
- [Unnamed thermal spring, UT](https://www.soakingsprings.com/hot-springs/utah/unnamed-spring-millard-county-3): 72°F source, pH 6.8, TDS 5,000 mg/L, Roadside, near Fillmore, Millard County

## Questions

**What is the water temperature at Springs?**
Springs has a water temperature of 68°F (20°C). This is a warm thermal spring.

**Where is Springs located?**
Springs is located in Beaver County, Utah at 5,020 feet elevation, near Milford. Coordinates: 38.7620°N, 112.8700°W.

**How do I get to Springs?**
Springs has Short Walk road access (0.2 mi from the road).

**What minerals are in the water at Springs?**
Water chemistry analysis shows the presence of pH, Total Dissolved Solids, Calcium, Magnesium, Sodium, Sulfate, Chloride. The pH is 7.5 (slightly alkaline). Total dissolved solids measure 558 mg/L.

## Sources

- USGS thermal springs records, Water Quality Portal lab analyses, OpenStreetMap, Wikipedia/Wikidata, NOAA climate normals